This comprehensive guide provides a detailed list of VCDS (VAG-COM) codes for Audi A5 models. These codes allow you to enable hidden features and customize your car’s settings beyond the factory defaults. While this information has been tested, proceed with caution and at your own risk. Incorrectly applying these codes could potentially damage your vehicle’s systems.
Accessing the Hidden Menu
Before using any codes, you’ll need to access the hidden menu in your MMI system. The process differs slightly depending on your MMI version:
MMI 3G:
- Navigate to [5F – Information Electr.]
- Select [Adaptation – 10]
- Change Channel 6 from 0 to 1.
- To access the hidden menu, press and hold the “CAR” and “SETUP” buttons simultaneously for five seconds.
MMI 2G:
- Navigate to [07 – Control Head]
- Select [Adaptation – 10]
- Change Channel 8 from 0 to 1.
- Access the hidden menu by pressing and holding the “CAR” and “SETUP” buttons simultaneously for five seconds.
Caution: Avoid modifying settings within the “Bootloader” section of the hidden menu.
Common Audi A5 VCDS Codes
Below are some popular VCDS modifications for the Audi A5:
Lighting Modifications
- Disable Amber Corner Lights (US Vehicles): [09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 10 Submodule 0 Bit 3 – Set to 0
- Disable LED “Wink” on Turn Signal (Pre-Facelift): [09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 3 Bit 2 & Bit 7 – Modify as needed (1 = active)
- Disable LED “Wink” on Turn Signal (Facelift): [09 – Cent. Elect.] [Security Access – 16] (code: 20113) [Adaptation – 10] -> Channel 3 – Set to 88
- Enable Rear Tail Lights with DRLs: [09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 2 Bit 7 – Set to 1 (Active)
- Enable Front Turn Signals as Parking Lights: [09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 10 Bit 0 – Set to 1, then Byte 2 Bit 6 – Set to 1
- Enable Fog Lamps with Turn Signals: [09 – Cent. Elect.] [Coding – 07] -> Long Coding Helper -> Byte 4 Bit 0 – Set to 1
Convenience Features
- Disable Seatbelt Chime: [17 – Instruments] [Coding – 07] -> Long Coding Helper -> Byte 0 Bit 2-4 – Modify Seat Belt Warning
- Enable Automatic Hill Hold Assist “Lite”: [03 – ABS brakes] [Security Access – 16] [Coding – 07] -> Long Coding Helper -> Byte 1 Bit 6 – Set to 1 (Certain ABS modules only)
- Enable Remote Operation of Windows and Sunroof: [46 – Cent. Conv.] [Coding – 07] -> Long Coding Helper -> Byte 2 Bit 2 – Set to 1
- Disable Key Warning (Keyless Models): [46 – Central Conv.] [Coding – 07] -> Long Coding Helper -> Byte 9 Bit 7 set to 0 (Uncheck)
- Enable Double Disarm Beep: [46 – Central Conv.] [Adaptation – 10] -> Channel 63 Add 4, Ensure Module 46, Byte 1, Bit 2 is ticked
Display and Media
- Enable Video in Motion on MMI: [5F – Information Electr.] [Advanced ID – 1A] (Use Security Access code from Serial Number) [Adaptation – 10] -> Channel 48 – Set to 255, Reset MMI
- Enable Speed Display on Chorus, Concert, or Symphony: Module 56 – Radio [Adaptation – 10] Channel 2 – Change 0 to 1 (Driving School Mode active)
- Enable Gauge Test/Needle Sweep: [17 – Instruments] [Coding – 07] -> Long Coding Helper -> Byte 1 Bit 0 – Check “Gauge Test/Needle Sweep active”
Other Modifications
- Adjust Bluetooth Microphone Sensitivity: Hidden Menu -> Diagnose -> Settings -> Mic Sensitivity
- Adjust Back-Up Camera Picture: [6C – Back-up Cam.] [Security Access – 16] (code: 22351) [Adaptation – 10] -> Adjust Channels 10-13 (Brightness, Contrast, Saturation, Temperature)
- Change MMI 3G Splash Screen: Hidden Menu -> car/carcodingvehicle -> Choose Model -> Update Splashscreen -> Restart MMI
This list represents a fraction of the available VCDS codes for the Audi A5. For a more extensive list and detailed instructions, consult reputable online forums dedicated to Audi vehicles and VCDS coding. Remember to always back up your original settings before making any changes. If you are unsure about any procedure, consult a professional. Enjoy customizing your Audi A5!
